N43259

HISTORY OF FLIGHTOn August 31, 2013, at 1357 Pacific daylight time, a single-seat experimental amateur-built Sport Copter Vortex, N43259, collided with the ground near Scappoose Industrial Airpark, Scappoose, Oregon. The gyroplane was registered to, and operated by, the pilot under the provisions of 14 Code of Federal Regulations Part 91. The student pilot was fatally injured. The gyroplane sustained substantial damage during the accident sequence, and was subsequently destroyed by post impact fire. The local personal flight departed Scappoose about 2 minutes prior to the accident. Visual meteorological conditions prevailed, and no flight plan had been filed.

A friend of the pilot reported that they had performed minor maintenance earlier that morning to the nosewheel. The pilot did not intend to take off, but rather had planned on performing a series of high speed taxi tests, and "crow hops." The friend further stated that the pilot had never soloed in a gyroplane before, with his only prior solo experience being a series of "crow hops" the previous weekend.

The friend witnessed and video-recorded the initial segment of the accident flight while positioned midfield on the west ramp. He stated that the gyroplane began the ground roll while traveling north on the parallel taxiway west of the runway 33. It took off, and seemed to be flying normally; however, as the pilot initiated the landing attempt, it became unstable and began to wobble. The pilot applied engine power and the gyroplane started to climb, and began a left turn towards the crosswind leg.

A second witness, who stated that he was a certified flight instructor with extensive helicopter and gyroplane flight experience, was located in his hangar at a similar vantage point, further north along the runway. He heard the sound of a gyroplane on the taxiway, and initially thought it was the aircraft of the accident pilot's hangar partner. He looked out and saw the gyroplane "crow hopping" down the taxiway, and then take off. It departed towards the north, and then began a left turn, climbing just over the hangars and trees, where it joined the downwind leg at what he considered to be a slow airspeed. He reported the engine sound as normal, and he did not see any smoke or vapor trailing at any time. He continued to be alarmed about the gyroplane's airspeed, and noted it was flying in a fairly "aggressive" nose-up attitude, while "mushing" through the sky. He was concerned that the pilot did not have complete control of the gyroplane. It then made what appeared to be a left base turn, while descending at a rapid rate. He assumed that the pilot was performing an "aggressive" descent to land, and thinking no more of it, went back into his hangar. A short time later he came back outside and saw smoke in the vicinity of where he last observed the gyroplane descending.

A third witness, located on an access road at the departure end of runway 33, about 1 mile from the accident site, observed the downwind portion of the flight. He reported that the gyroplane was flying 200 feet above the surrounding trees. He looked away briefly, and as his gaze returned, the gyroplane shape had changed. He could now see the full disc of the rotor blades, and the fuselage appeared to spin. The gyroplane then tumbled, and rapidly descended to the ground.

Video

Review of the video footage revealed that it closely matched the witnesses' statements. It depicted the gyroplane taxing south along the taxiway with the engine running and rotor blades spinning appropriately. In the next video segment, the gyroplane was airborne and flying north directly over the taxiway, about 30 feet above ground level (agl). As it passed midfield while still over the taxiway, the engine tone decreased in pitch, and the gyroplane yawed to the left and began a rapid descent to about 25 feet agl. The engine tone then increased, the gyroplane recovered, and began to climb. Once the gyroplane reached the end of the taxiway, it began a climbing left crosswind turn to about 150 feet agl. In the final video segment the gyroplane was about 300 feet agl, and was proceeding south on the downwind leg. The video resolution prevented an accurate assessment of the gyroplane's attitude, but the main rotor blades were turning, and the engine was operating. The gyroplane was not trailing any smoke or vapor in any of the recordings. PERSONNEL INFORMATIONThe 59-year-old-pilot held a combined student pilot and third-class aviation medical certificate issued October 29, 2012, with limitations that he must have available glasses for near vision. An examination of his logbook indicated a total flight experience of 26.8 hours since his first training flight on July 30, 2012, through to his most recent logbook entry 11 days prior to the accident. His initial flight training took place in a Cessna 152 fixed wing airplane for the period of July 30, 2012, to December 1, 2012, during which time he accumulated 17 hours of dual flight instruction. He began dual flight instruction in a Calidus gyroplane in Utah on July 23, and by August 15, had accumulated 8.7 hours of flight time.

His last flight entry was for dual instruction in a Vortex II gyroplane, which took place in Scappoose. Neither his flight logbook, nor student pilot certificate contained any entries endorsing him for solo flight, and the flight instructor who provided him with his most recent flight training stated that he was not ready for solo flight. No entries were located indicating any flight experience in the accident gyroplane. AIRCRAFT INFORMATIONThe single engine gyroplane was comprised of a tubular aluminum and steel primary structure with composite cabin fairings, and aluminum-skinned vertical and horizontal stabilizers. It was equipped with a Rotax 618 series two-stroke engine, and a three-blade composite propeller.

The gyroplane was manufactured as a kit, and built by the original owner, receiving its special airworthiness certificate in May 2005. Federal Aviation Administration (FAA) records indicated that the accident pilot purchased the gyroplane from this owner in July 2010. No maintenance logbooks were recovered. METEOROLOGICAL INFORMATIONAn automated surface weather observation from Scappoose was issued 4 minutes before the accident. It indicated calm wind and clear skies, with a temperature of 29 degrees C, dew point 12 degrees C, and an altimeter setting at 29.87 inches of mercury. AIRPORT INFORMATIONThe single engine gyroplane was comprised of a tubular aluminum and steel primary structure with composite cabin fairings, and aluminum-skinned vertical and horizontal stabilizers. It was equipped with a Rotax 618 series two-stroke engine, and a three-blade composite propeller.

The gyroplane was manufactured as a kit, and built by the original owner, receiving its special airworthiness certificate in May 2005. Federal Aviation Administration (FAA) records indicated that the accident pilot purchased the gyroplane from this owner in July 2010. No maintenance logbooks were recovered. WRECKAGE AND IMPACT INFORMATIONThe NTSB investigator traveled in support of this investigation, and performed an examination of the engine and airframe following recovery.

The gyroplane came to rest on an easterly heading in a field, about 950 feet west-northwest of the approach end of runway 33. The entire structure was contained within the immediate vicinity of the impact site. A group of 130-foot-tall trees bordered the area 50 feet to the north; all of the trees were intact, and did not show any indications of recent damage.

The fuselage was positioned on its left side, and had sustained extensive thermal damage from the aft section of the tail keel through to the rotor mast, consuming most of the cabin structure, flight controls, and structural members. The gyroplane displayed damage signatures consistent with striking the ground in a left-side-low, nose-down attitude, with the vertical stabilizer and rudder bending over the left horizontal stabilizer. MEDICAL AND PATHOLOGICAL INFORMATIONAn autopsy was performed by the Oregon State Police, State Medical Examiner. The cause of death was reported as the result of multiple fractures and internal injuries.

Toxicological tests on specimens recovered from the pilot were performed by the FAA Civil Aerospace Medical Institute. Analysis revealed no findings for carbon monoxide, and the results were negative for all screened drug substances and ingested alcohol. Refer to the toxicology report included in the public docket for specific test parameters and results. TESTS AND RESEARCHThe gyroplane was recovered from the accident site, and examined by the NTSB investigator-in-charge, along with an inspector from the FAA, and a representative from Sport Copter. The examination did not reveal any anomalies with the airframe or engine that would have precluded normal operation. The following is a summary of the airframe and engine examination; a detailed report is located within the public docket.

Mast and Rotor Assembly

The rotor assembly sustained minimal thermal damage, and remained largely intact. The folding mast clamp remained intact, and connected to the mast support tubes. The support tubes and mast were thermally consumed about three feet below the clamp. The rotor head pivot bolts remained intact, and the assembly could be pivoted by hand to the stops in both the longitudinal and lateral directions.

All rotor assembly bump stops, bushings, plastic washers, and pivot plates, exhibited significant contact damage, gouge marks, and grazing consistent with over-travel of the primary rotor system components.

Main Rotor Blades

Both main rotor blades remained attached to the blade hub bar, which was connected to the teetering hinge within the rotor head. The first blade exhibited a 10-degree downward curve along its entire length. No leading edge or chord wise scratches or gouges were present, and the trailing edge exhibit...