N41SH

HISTORY OF FLIGHT

On June 19, 1998, at 2144 eastern daylight time, a Cessna CE-500, N41SH, was substantially damaged when it overran the runway while landing at Elizabeth Field, Fishers Island, New York. There were no injuries to the two certificated airline transport pilots and two passengers. Visual meteorological conditions prevailed for the corporate flight that originated from Teterboro, New Jersey. No flight plan had been filed for the flight that was conducted under 14 CFR Part 91.

In a written statement the pilot reported:

"...Upon touch down at the numbers of Runway 12...[the co-pilot] deployed the speed brakes and I started to apply the brakes, at first we started to decelerate then both brake peddles became hard and all braking failed to decelerate the aircraft. I yelled to...[the co-pilot] to hold the control wheel and we lost the brakes, at the same time I reached for the Emergency Brake Control and my shoulder harness locked and prevented me from reaching the Emergency Brake Control. I then shut down both engines while steering the aircraft to the right side of the runway and still attempting to reach the Emergency Brake Control. Upon the aircraft right wing tip contacting the stone sea wall beyond the right side of the runway, my shoulder harness released and I struck the Instrument panel as the aircraft rotated to the right and pitched up and then stopped."

"After the aircraft came to rest I yelled to...[the co-pilot] to get to the door and evacuate our passengers, I secured the cockpit and then went for the emergency exit. [The co-pilot]...could not open the [main cabin] door and yelled that it was jammed, I was successful in opening the emergency exit and directed all persons out of the exit and away from the aircraft...."

The co-pilot stated:

"...on final approach to runway 12. The wind was calm, conditions were VFR, and the runway was dry. [The pilot]...landed the airplane at the beginning of the runway at Vref. I deployed the speed brakes. Initially, I felt a slight deceleration, but immediately thereafter we stopped decelerating. [The pilot]...shouted towards me that he had no brakes. I quickly glanced over towards him and noticed that he was standing hard on the brakes, but nothing was happening. [The pilot]... shut down the engines quickly while I helped hold the yoke back. Toward the end of the runway, he turned the aircraft hard to the right. It impacted some rocks and climbed up onto them. Upon stopping, I tried but was unable to open the main cabin door. [The pilot]...opened the emergency hatch, and we all exited there...."

A witness sitting on his front porch reported that when he first saw the airplane, it was higher than normal, did not appear to be on the ground yet, and he thought it was going to land long. He then heard brakes or tires, which squealed and he heard the crash. He went inside and called 911, and then went to the firehouse as he was a volunteer fireman and proceeded to the accident sight. When he got to the accident site, the runway was dry.

Interviews with the emergency personnel who responded to the accident site revealed several people had reported observing a single tire mark that led to the airplane. One witness did report seeing a fainter second tire mark from what he thought was the left main wheel. The runway was reported as dry.

In follow-up telephone interviews, the pilot reported he did not conduct a rejected landing because when he lost the brakes, he felt there was insufficient runway to successfully complete a rejected landing. The co-pilot reported they had completed the anti-skid check prior to landing and the system checked OK.

AIRCRAFT INFORMATION

The airplane was a 1975 Cessna CE-500. It had been modified in accordance with Sierra industries, Inc Supplemental Type Certificate (STC) SA 2172 NM, for the long wing modification, and Aviation Brake Systems, Ltd, STC SA2925 WE, for the addition of an anti-skid system.

The airplane was delivered with an unpressurized, toe-actuated, multiple disk brake system. A pneumatic backup emergency brake control handle was installed under the left instrument panel. The anti-skid system pressurized the existing wheel brake system. According to the anti-skid system flight manual supplement:

"The Power Brake and Skid Control Systems are energized when the System Switch is placed in the 'ANTI-SKID' position and the aircraft Master Switch is 'ON'. The Power Brake and Skid Control Systems are disengaged when the System Switch is in the 'MANUAL' position; however, the accumulator will provide diminishing Power Brake (but NOT Skid Control) capability for about 20 minutes or 16 brake applications (whichever comes first) after System Switch is selected 'MANUAL'."

"The brake pedals will have a 'firm feel' feel when the system is energized. The brake pedals will feel 'soft' and have greater 'travel' when the system is disengaged, similar to that in the unmodified airplane."

"NOTE: The system operates in the 'power brake' mode at all speeds; however, the anti-skid feature of this system is operational only at speeds above 15 MPH."

"CAUTION: The 'ANTI-SKID INOP' lights should always be illuminated, when the 'POWER BRAKE LOW PRESSURE' lights are illuminated. Illumination of the 'ANTI-SKID' lights alone indicates that the system is in the power brake mode WITHOUT anti-skid protection. In this event, follow ABNORMAL PROCEDURES...."

"ABNORMAL PROCEDURES - All probable system failures will either be annunciated or detected by improper results during NORMAL PROCEDURES checks. In all such cases: 1. Place the system switch in the 'MANUAL' position. 2. Bleed off the 'boost pressure' by repeated application of the brakes. The 'boost pressure' has been depleted when the pedals feel 'soft' and have an increased 'travel'. 3. Manual Braking ONLY will then be available...."

The insurance adjuster reported that the emergency brake air bottle was properly charged.

AIRDROME INFORMATION (Destination)

Elizabeth Field Airport was an uncontrolled, unattended airport. According to FAA data, runway 12 was 2,328 feet long, 100 feet wide, and had an asphalt surface. Medium intensity runway edge lights were on the sides of the runway. The data also indicated that a two light PAPI was available on the left side of the runway with a 3 degree glideslope, and runway end identifier lights. No information was listed on overruns, or displaced thresholds.

According to the pilot, after the accident, he measured the overrun on each runway and found the landing overrun measured 115 feet for runway 12, and 240 feet for runway 30.

The insurance adjuster reported that the first runway light on the north side of runway 12 was inoperative.

WRECKAGE AND IMPACT INFORMATION

The airplane had been delivered to a salvage company prior to start of the investigation. Copies of photographs and written reports were requested and received from the Federal Aviation Administration and the insurance adjuster. The photographs revealed the airplane departed the end of the runway on the right side and came to rest on a rock sea wall. The nose landing gear had collapsed rearward and the underside of the fuselage was bent in a wavy manner. The right wing tip had separated from the airplane and the outer spar on the right wing was distorted and bent rearward. There was a fuel leak from the right wing. A single tire mark was visible, about 10 to 15 feet right of runway centerline. The tire mark then curved to the right and departed the end of the runway on the right side, pointing toward the airplane. The pilot identified the tire mark, which alternated between heavy and light, as coming from the right main landing gear tire.

According to the insurance adjuster's report, "...The first significant skid marks on RWY 12 are 612 ft from the threshold. The right tire make a significant skid while the left made light intermittently skipping skid marks...."

ADDITIONAL INFORMATION

Safety Board Notification & History of Previous Investigation

The Safety Board received initial notification of the occurrence on the night of the accident. Inspectors from the FAA Flight Standards Office located at Farmingdale, New York, traveled to the accident site on June 20, 1998, and conducted an on-site examination. They informed the Safety Board investigator that the damage was below the threshold of an accident. Therefore, the Safety Board did not conduct an investigation.

On June 27, 1998, the insurance adjuster examined the brakes. There is no record of any discrepancies being found.

On July 24, 1998, the anti-skid system was examined by Columbia Air Services, Inc. The examination found shorted wires between the right transducer to the anti-skid box connector. No other problems were noted.

On July 29, 1998, Columbia Air Services, sent a letter to the FAA Airworthiness inspector assigned to the investigation. The letter included a complete description of the examination and findings including the shorted wires, and the following:

"...I also spoke with the Engineering Department at Crane Hydro-Aire and was told the Control Box has a time signal delay and if the short was happening fast enough, and not lasting that [long] the control box may not send out the signal to illuminate the 'Anti-skid inop light.'

No documentation was available to indicate further investigation was done or any follow-up was conducted with Crane Hydro-Aire to know the significance of the shorted wires or the anti-skid light not illuminating.

On August 4, 1998, the FAA closed out the investigation with the following comment:

"...Follow-up by maintenance revealed no abnormalities with brakes, hydraulics, or anti-skid system."

On November 16, 1998, the pilot sent a letter to the FAA Eastern Region, Regional Counsel. In it he expressed concern in several area and included the following comment:

"...this should be an a...