N323D

HISTORY OF FLIGHT

On April 13, 2003, about 1230 mountain standard time, a Beech A36, N323D, collided with a fence and then terrain during takeoff from runway 21 at Sedona, Arizona. Mesa Pilot Development, Inc., was operating the airplane under the provisions of 14 CFR Part 91. The certified flight instructor (CFI) pilot, the private pilot undergoing instruction (PUI), and one passenger sustained fatal injuries; the airplane was destroyed. The instructional cross-country flight was en route to Williams Gateway Airport, Phoenix, Arizona. Visual meteorological conditions prevailed, and an instrument flight rules (IFR) flight plan had been filed. The primary wreckage was at 34 degrees 50.63 minutes north latitude and 111 degrees 47.69 minutes west longitude.

Several witnesses observed the takeoff roll. They all noted that the airplane did not seem to accelerate and was rolling very slowly as it passed the midfield point. Several of the witnesses noted that the flaps were partially down. The witnesses thought that the pilot would abort the takeoff. However, the airplane continued down the runway and was still on the ground about 80 percent of the way down the runway. Then the pilot rotated it to a takeoff attitude. Several witnesses thought that it retained that attitude, and if it left he ground at all, it only attained an altitude of several feet.

Several of the witnesses that heard the engine reported that it did not sound like it was producing much power. The engine tones stayed steady and the engine sounded smooth. It did not cough, sputter, or backfire, and none of them observed smoke or any indications of a problem.

Another witness on the opposite side of the airport heard clanking and banging that sounded like a thresher machine. It was definitely not smooth or sound like engines that he had previously heard. It caught his attention and he looked toward the runway. He saw the top of a tail and fuselage. He estimated that the airplane was going about 70 miles per hour. He did not hear the engine wind down and wondered why it was trying to take off. He lost sight of the airplane behind trees and did not see it rotate. He thought that it was within 1,000 feet of the end of the runway. About 5 to 10 seconds later he heard a bang, and about 10 seconds later he heard another bang.

One witness was a CFI, and an airplane mechanic with 30 years experience in general aviation. He first saw the airplane about 1/3 of the way down the runway. From the moment he saw it, he thought that something was not right. He was concerned that it was not accelerating to flying speed. The engine sounded quite different from airplanes that he had heard over his career. It sounded like it was turning very slowly, much slower than takeoff revolutions per minute (rpm). He thought that the propeller was set to cruise power rather than full rpm. It sounded like it was turning about 2,300 rpm. It sounded smooth; it did not backfire, surge, miss, or chug. It sounded the same from the time that he first saw it until it went out of sight. Other airplanes that he had observed take off had been airborne by this point. The accident airplane kept going and going. It went past the halfway point and was not accelerating. The witness kept saying, "shut down, shut down." It broke ground about 2/3 to 3/4 of the way down the runway, maybe beyond 3/4. He left his chair to watch the airplane. He noted that the nose came up and the airplane continued down the runway about 200 yards with the nose wheel off the ground and the main gear on the ground. It might have gotten airborne about 1 or 2 feet. The airplane broke ground with an extremely nose high attitude. He lost sight of it behind a parked airplane. He thought that the stall horn had to be going off.

PERSONNEL INFORMATION

The operator submitted a written report.

CFI

A review of Federal Aviation Administration (FAA) airman records revealed that the CFI held a commercial pilot certificate with ratings for airplane single engine land, multiengine land, and instrument airplane. She held a certified flight instructor certificate with ratings for airplane single engine land and instrument airplane.

The CFI held a first-class medical certificate issued on May 9, 2001. It had no limitations or waivers.

The operator reported that the CFI had a total flight time of 652 hours. She had 136 hours in the last 90 days, and 32 in the last 30 days. She had 50 hours in this make and model.

PUI

The operator reported that the PUI had a private pilot certificate with a rating for airplane single engine land. He had a total flight time of 174 hours. He had 34 hours in the last 90 days, and 14 in the last 30 days. He had 37 hours in this make and model, and was preparing for his instrument check ride.

AIRCRAFT INFORMATION

The airplane was a Beech A36, serial number E2613. The operator reported a total airframe time of 2,249 hours. The airplane was on a manufacturer's inspection program, and the last 100-hour inspection occurred on March 12, 2003. The tachometer read 1,748.2 and the Hobbs hour meter read 270.2 at the daily inspection prior to departure for Sedona.

The engine was a Teledyne Continental Motors IO-550-B(6) engine, serial number 296594R. Time since overhaul on the engine at the last inspection was 514 hours.

The operator indicated that the last fueling of the airplane occurred on April 12 with the addition of 36 gallons of aviation fuel. The airplane flew 0.8 hours on one flight prior to the accident flight.

METEOROLOGICAL INFORMTION

The Sedona airport administration office reported the weather conditions: skies clear; winds from 170 degrees at 11 knots gusting to 24 knots; temperature 68 degrees Fahrenheit; altimeter 30.05 inches of mercury.

AIRPORT INFORMATION

The Airport/ Facility Directory, Southwest U. S., indicated runway 21 was 5,132 feet long and 75 feet wide. The runway surface was asphalt, and the airport elevation was 4,827 feet.

WRECKAGE AND IMPACT INFORMATION

The National Transportation Safety Board investigator-in-charge (IIC) and investigators from the FAA, Beech, and Teledyne Continental Motors (TCM) examined the wreckage at the accident site on April 14, and at the facilities of Air Transport, Phoenix, on April 15. Safety Board software determined that the airplane came to rest approximately 1,032 feet on a magnetic bearing of 213 degrees from the airport.

Sedona airport is on a plateau that is surrounded by rocky canyons about 500 feet deep that are sparsely covered by cedar trees and bushes. The airport boundary fence was a 6-foot-high chain link fence with angled barbed wire strands another foot high. The fence ran along the edge of a canyon that began at the end of the runway. The fence was about 150 feet from the end of the runway. It sustained mechanical damage about 100 feet right of the extended centerline. The top part of the fence was deformed and pieces of barbed wire and fence posts were on the ground on the side of the fence away from the runway.

The main wreckage was on the opposite side of the canyon from the airport boundary. It was several hundred feet lower than the airport boundary fence.

The first identified point of contact (FIPC) was a cedar tree with broken limbs. Another cedar tree, about 10 feet right of the FIPC as one looked toward the main wreckage, also had broken limbs. Near the base of this tree were clear Plexiglass fragments similar in shape to the wing tip recognition lights' covers. The debris path was along a magnetic bearing of 185 degrees.

Thirty-three feet from the FIPC was the right main landing gear. Pieces of propeller, identified as prop piece 2 and prop piece 1, were 36 and 38 feet from the FIPC, respectfully.

The principle impact crater (PIC) was 46 feet from the FIPC. A scorched area about 6 feet in diameter surrounded the PIC. The left elevator counterweight separated and was just past the scorched area. It was not scorched and had scrapes along its edge and a dent along its front edge.

The main wreckage came to rest 85 feet from the FIPC. The main wreckage pointed along a magnetic bearing of 190 degrees. The separated left main landing gear was at the trailing edge of the left elevator. The left main gear had pieces of wire around it that were similar to the airport boundary fence. Fire consumed the cabin area. A scorched area extended from wing tip to wing tip, and from the nose of the engine to mid empennage. The tail area was outside of the scorched area and did not sustain thermal damage. About 6 feet of the outboard left wing bent up about 30 degrees.

About 10 feet right of the right elevator was the propeller. The propeller was outside of the scorched area and it did not exhibit thermal damage. A piece of propeller, identified as prop piece 3, was between the propeller and the main wreckage.

The engine separated from the airframe and rotated to a magnetic bearing of 235 degrees. The left side of the engine was downslope and sustained more thermal damage than the right side.

MEDICAL AND PATHOLOGICAL INFORMATION

The Yavapai County Coroner completed an autopsy on both pilots. The FAA Bioaeronautical Sciences Research Laboratory, Oklahoma City, Oklahoma, performed toxicological testing of specimens of the pilots.

Analysis of the specimens of the PUI contained no findings for carbon monoxide, cyanide, volatiles, or tested drugs.

TESTS AND RESEARCH

Wreckage Examination

Investigators established control continuity for all control surfaces. The airframe manufacturer's representative determined that the landing gear was in the down position. The representative measured the flap actuator at 4.4 inches. He reported that this corresponded to the 15 degrees flaps down position. The left aileron trim actuator measured 1.78 inches. He reported that this equated to 4.75 degrees tab up position. The elevator trim measured 1.4 inches. He...