N4029Q

HISTORY OF FLIGHT

On November 27, 2004, about 0935 Pacific standard time, a Robinson R22 Beta helicopter, N4029Q, registered to and operated by a private individual, was destroyed while maneuvering when it experienced an in flight break-up followed by impact with the terrain during an uncontrolled descent near Arlington, Washington. The flight instructor and the pilot-rated student sustained fatal injuries. Visual meteorological conditions prevailed and a flight plan was not filed for the 14 CFR Part 91 instructional flight. The local flight departed the Arlington Municipal Airport (AWO), Arlington, Washington, at approximately 0930.

In a statement submitted to the National Transportation Safety Board investigator-in-charge (IIC), two witnesses reported that on the morning of the accident, at approximately 0920, they observed the helicopter being started and lifting off the ground before moving to the run-up area, which is located at the southeast corner of runway 34-16. The witnesses stated that the helicopter then settled onto the ground facing north-northwest [320 degrees], and remained there for the next 2 minutes at takeoff RPM. The witnesses reported that the helicopter then lifted off the ground to about 3 to 4 feet before turning slightly to the right, then making a left turn of approximately 320 degrees before slowly accelerating and aligning itself parallel to the taxiway. The witnesses stated that the helicopter then slowly climbed to 75 to 100 feet above ground level (agl) before departing to the north, and at all times the helicopter sounded normal and was very smooth in flight.

Numerous witnesses reported seeing the helicopter flying between 300 and 500 feet agl and heading north before experiencing an in flight breakup and impacting terrain. One witness reported hearing what he thought "…was the engine making a loud noise, like a large diesel truck roaring, then there was a large, loud bang north of my barn and some pieces fell to the ground." A second witness reported hearing the helicopter "...make a loud bang, then watched it fall from the sky." A third witness reported seeing a small helicopter flying off to his left, "...and [in] a matter of seconds I saw smoke from where the helicopter was flying. I saw the aircraft crash into the field." A fourth witness reported seeing a small helicopter flying north from AWO, "...and as it disappeared into the distance I heard a large prolonged 'shuddery boom,' and then no more helicopter engine noise."

The NTSB IIC and two Federal Aviation Administration (FAA) aviation safety inspectors traveled to the accident site. The helicopter was located in an open field approximately 2 nautical miles north of AWO. There was no post crash fire. After an initial onsite examination of the aircraft and documentation of the debris field, the helicopter and all associated components were recovered and moved to a secured location at the Arlington Municipal Airport, where representatives from the NTSB and the FAA would examine the wreckage in greater detail at a later date.

The helicopter, which had been purchased by the pilot-rated student three days prior to the accident, had been rebuilt by a local certificated airframe and powerplant mechanic. The mechanic personally delivered the helicopter to the pilot-rated student at approximately 1800 on November 24th. In a telephone interview with the IIC on November 28th, the mechanic reported that on November 16th and 17th, he conducted test fights of the helicopter with the assistance of another pilot. The test pilot stated in a telephone interview with the IIC that he observed no anomalies with the aircraft during the test flight. The test pilot also revealed that on November 25th, the day after the new owner purchased the helicopter, he personally flew with him for approximately 45 minutes, letting the pilot/owner take control of the aircraft during various portions of the flight. Additionally, the mechanic had a second pilot conduct a test flight on November 24th. In a written report to the IIC, the second test pilot stated that the mechanic requested that he take the helicopter up and put it into an autorotation, checking to make sure that the main rotor blades were adjusted properly. The test pilot reported taking the helicopter up to 1,000 feet, dropping the collective, and observing the rotor RPM to be low. The pilot stated, "I landed and reported my findings to [the mechanic], [who] made some adjustments. I did another flight and found the rotor RPM was now where it should be. At the time of my flight this ship had the same doors on it that I fly with (Tech-Tool doors)." The mechanic reported that the total time for all of the test flights was 4.1 hours.

In a statement provided to the IIC dated November 29, 2004, the mechanic reported that the helicopter's annual inspection was completed and the aircraft was delivered to the pilot-rated student about 1800 on November 24th. The mechanic further reported that the Tech-Tool doors were properly installed and that the [door] pins were all in place. The mechanic stated that on November 24th, prior to delivering the helicopter to the pilot-rated student, "...I told him that he would have to reinstall the original factory doors before flying the helicopter, because I had not finished the weight and balance for the Tech-Tool doors."

Two witnesses provided the IIC with statements relative to their personal observations during the days prior to the accident. The first witness reported that after observing the helicopter being test flown on November 24th and put back in front of its hangar, he noticed that the [door] pins were not in the doors. The witness further reported that on Friday, November 26th, he again noticed that the helicopter's [door] pins were not installed. The second witness reported that about 1100 on the day before the accident, November 26th, while in the owner's hangar looking the helicopter over, "I commented to [the owner] that the cotter pins were missing or not installed to hold the doors on." The witness stated that the owner told him he was aware of this and that there were a couple of small scratches on the left door window that he would have to remove.

PERSONNEL INFORMATION

The flight instructor, who occupied the left pilot seat, was a full time employee for a local emergency medical air ambulance operator. The flight instructor held a rotorcraft-helicopter airline transport pilot certificate, with commercial privileges for airplane single and multiengine land, and instrument airplane. The pilot also possessed a flight instructor certificate for airplane single-engine, rotorcraft-helicopter, and instrument airplane and helicopter. The flight instructor possessed an FAA Class 1 medical certificate dated March 16, 2004, with a limitation to wear corrective lenses. The pilot reported on his most recent airman medical application a total flying time of 8,100 flight hours, with 150 hours accumulated in the previous 6 months.

The pilot-rated student, seated in the right seat, was receiving his first instructional flight in the helicopter, which he had just purchased three days prior to the accident. At the time of the accident the pilot-rated student held a private pilot certificate for single-engine land airplanes. The pilot also possessed an FAA Class I medical certificate dated March 8, 2004, with a limitation to wear lenses that correct for distant vision, and possess glasses that correct for near vision. On the application for the medical certificate, the pilot reported his total flight time was 300 hours, with 25 hours flown in the previous six months.

AIRCRAFT INFORMATION

The two-seat Robinson R22 Beta helicopter, serial number 1529, was issued a standard airworthiness certificate on May 7, 1991. A review of the helicopter's maintenance records revealed the most recent annual inspection was completed on November 24, 2004, with a total airframe time of 2728.3 hours. The Hobbs hour meter read 4.1 hours at the last annual inspection and 4.5 hours at the accident site.

The aircraft had a Textron Lycoming O-320-B2C engine, serial number L-171189-39A. Total time on the engine at the last annual inspection was 502.1.

In a statement provided to the IIC on November 28, 2004, the certificated airframe and powerplant mechanic reported that during the rebuild of the helicopter the tail rotor gearbox was sent to Robinson Helicopter Company to be repaired; total time on the gearbox was 575 hours, with a time between overhaul (TBO) of 2,200 hours. The mechanic further reported that the overrunning clutch was also sent to Robinson Helicopter Company to be repaired; total time on the clutch was 575 hours, with a TBO of 2,200 hours. The mechanic stated that the main rotor blades were timed out, with blade life being 2,200 hours; the blades had 13 to 14 hours left on them when the helicopter was sold. The mechanic reported the tail rotor blades had accumulated 832.5 hours, and, were life limited at 5,520 hours, the main rotor transmission was new with zero time, and the actuator had a total of 218 hours, with a TBO of 2,200 hours.

In a subsequent conversation with the mechanic who rebuilt the helicopter, the mechanic stated to the IIC that the reason the helicopter was being rebuilt was that the pilot-rated student had requested that the mechanic rebuild the helicopter to his specifications. The mechanic stated that the rebuild did not commence until the pilot-rated student made the request; there was no repair work done to the helicopter prior to this time.

METEOROLOGICAL INFORMATION

At 0853, the Automated Surface Observing System (ASOS) at the Snohomish County Airport/Paine Field (PAE), located 17 nautical miles south-southwest of the accident site, reported wind 300 degrees at 9 knots, visibility 10 statute miles, light rain showers, scattere...