N182PJ

HISTORY OF FLIGHTOn May 21, 2014, at 0810 eastern daylight time, a Cessna 182S, N182PJ, was substantially damaged during a runway overrun at Cecil County Airport (58M), Elkton, Maryland. The airline transport pilot and two passengers were not injured. Instrument meteorological conditions prevailed, and an instrument flight plan had been filed for the personal flight from Penn Valley Airport (SEG), Selinsgrove, Pennsylvania, to Albert Ellis Airport (OAJ), Jacksonville, North Carolina, conducted under the provisions of 14 Code of Federal Regulations Part 91.

According to the pilot's written statement, while climbing to a cruising altitude of 8,000 feet above mean sea level (msl), he encountered light turbulence and light to moderate rain for the first 30 minutes, and flew in continuous instrument meteorological conditions (IMC). Shortly after crossing the Pennsylvania/Maryland border, he requested a different routing due to heavy rain showers, which was approved by air traffic control (ATC).

Once the airplane was established at 8,000 feet msl, the pilot leaned the mixture to "lean of peak," closed the cowl flaps, and adjusted the power setting for cruise flight. At this time, the airplane was flying through continuous rain showers and the outside temperature was 39 degrees Fahrenheit, so he turned on the pitot heat. Several minutes after leveling off, he noticed that the exhaust gas temperature gauge was not functioning properly. The fuel flow indication was appropriate, and all other engine instrument gauges were reading normal. He also noted that the autopilot was unable to operate in "NAV" mode, and rocking slightly left and right in "HDG" mode. Shortly thereafter, the pilot lowered the volume on the radio panel because it was too loud in his headset. Afterwards, he noticed that the next time he spoke to ATC he could barely hear his own voice, so he increased the volume.

To avoid other traffic, ATC advised the pilot to fly a 160 degree heading. When he replied, the pilot again could not hear his own voice in his headset, but was acknowledged by ATC. Shortly thereafter, the instrument panel blinked rapidly several times and then the airplane experienced a total electrical failure. The transponder, both communications radios, the GPS, the airborne weather display, the ADF, attitude indicator, autopilot, and all electrically driven equipment "went off" and stopped functioning. The airplane was in IMC conditions and the pilot immediately focused on hand-flying the airplane on the assigned heading and altitude.

The pilot was unable to contact ATC. He did not have a handheld radio and did not have cellular phone service at 8,000 feet msl. He then turned off the pitot heat, checked the circuit breakers and tried to recycle the autopilot, transponder, and radios, but was not able to restore electrical power.

The pilot utilized an application on his iPad computer tablet to determine that the nearest airport with a paved runway was 58M, which was located approximately 8 miles northeast of his position. He diverted to 58M and was able to begin to see the ground at approximately 3,000 feet msl, with a significant scattered and haze cloud layer below, and what appeared to be a few miles visibility. One of the passengers was able to call ATC on his cellular phone to report the situation and the pilot's intentions.

The pilot identified the airport roughly 2 miles out and entered the traffic pattern. He decided to land on Runway 13, "which did not have a displaced threshold, and had a clear approach." Due to the electrical failure, the flaps could not be extended. The pilot flew an extended downwind leg of the traffic pattern and attempted a no-flap landing. He stated that knew the runway was nearly 3,000 feet long and felt confident that he could land in that distance since he had done it many times before. He did not want to risk continued flight in IMC conditions with an airplane with a complete electrical failure.

The pilot conducted an elongated shallow approach at a speed of "75 knots." Upon reaching the runway, he immediately put the main wheels aggressively on the runway, and applied full brakes. There was no reaction when he pushed on the brakes. The airplane did not skid, slip, squeal, or slide at all; it just rolled straight down the runway without decelerating. The pilot pushed the control wheel forward in an attempt to put more weight on all of the wheels. Both he and the passenger pushed hard on the brakes, but the airplane did not slow down and was at least halfway down the runway. The pilot decided not "go-around" based on the trees and power line at the end of the runway, the IMC conditions, nearly full fuel, three large adult passengers with luggage, and the uncertainty of what was wrong with the airplane.

The pilot pulled the emergency (parking) brake handle, and intentionally deviated off the left side of the runway, in an attempt to utilize an airport access road for additional stopping distance. The airplane subsequently struck a fence, and other obstacles before it came to rest approximately 10 feet off the shoulder of a road which was located along the southeast side of the airport.

The pilot advised that he was not previously aware that the runway contained a significant downhill gradient and had been sealed with a weather sealant.

Review of ATC voice recordings revealed that after the accident, the pilot advised ATC that he had "landed long on the runway" and "bent the airplane up." PERSONNEL INFORMATIONAccording to Federal Aviation Administration (FAA) and pilot records, the pilot held an airline transport pilot certificate with ratings for airplane multiengine land, and airplane single-engine land and a type rating in the CE-525S. He also held private pilot certificate for rotorcraft. His most recent FAA third-class medical certificate was issued on October 5, 2012. He reported that he had accrued approximately 3,960 total flight hours. AIRCRAFT INFORMATIONThe accident airplane was a four place, high-wing, single engine airplane of conventional construction. It was equipped with tricycle landing gear, and single slot type electrically controlled wing flaps.

According to FAA and airplane maintenance records, the airplane was manufactured in 1998. The airplane's most recent annual inspection was completed on June 1, 2013. At the time of accident, the airplane had accrued approximately 1,103 total hours of operation.

Electrical System

The airplane was equipped with a 28-volt, direct current electrical system. The system was powered by a belt driven, 60-amp alternator and a 24-volt battery, located in the tailcone area, aft of the baggage compartment. Power was supplied to most general electrical circuits through a split primary bus bar (Electrical Bus No. 1 and Electrical Bus No. 2), with an essential bus (Essential/Crossfeed Bus) wired between the two primaries to provide power for the master switch, annunciator circuits, and interior lighting.

Each primary bus bar was also connected to an avionics bus bar (Avionics Bus No.1 and Avionics Bus No.2) via a single avionics master switch. The primary buses were on anytime the master switch was turned on, and were not affected by starter or external power usage. The avionics buses were on when the master switch and avionics master switch were in the "ON" position.

The airplane used a power distribution module (J-Box) located on the left forward side of the firewall, to house all relays used throughout the electrical system. In addition, the alternator control unit (ACU) and the external power connector were housed within the module.

Ammeter/Vacuum Gauge

The airplane was equipped with an ammeter/ vacuum gauge which was located on the lower left side of the instrument panel. It indicated the amount of current, in amperes from the alternator to the battery, or from the battery to the airplane electrical system. When the engine was operating and the master switch was on, the ammeter would indicate the charging rate applied to the battery. In the event that the alternator was not functioning, the ammeter would have indicated a battery discharge rate.

Annunciator Panel

An annunciator panel was located above the avionics stack and provided caution (amber) and warning (red) messages for selected portions of the airplane systems. Inputs to the annunciator came from each fuel transmitter, the oil temperature transducer, low oil pressure switch, the vacuum transducer, and the ACU.

The low voltage warning light in the annunciator panel would activate anytime the voltage would fall below 24.5 volts. If low voltage was detected, the red annunciation "VOLTS" would flash for approximately 10 seconds to gain attention of the pilot before illuminating steadily. Once illuminated, the pilot would not have been able to turn off the annunciator.

Wing Flap System

The wing flap system received its electrical power from Electrical Bus No.2 and was protected by a 10-ampere circuit breaker labeled "FLAP" on the lower left side of the control panel.

The single slot-type wing flaps could be extended or retracted by positioning the wing flap switch lever on the instrument panel to the desired flap deflection position (10,20, or 30 degrees). In order to do this, the switch lever was moved up or down in a slotted panel that provided mechanical stops at the 10 and 20 degree positions. To change flap settings, the flap lever was moved to the right to clear the mechanical stops at the 10 and 20 degree positions. A scale and pointer to the left of the flap switch would indicate the flap travel in degrees.

Lift and drag could be varied by the pilot through the use of this system. Flap extension during landings provided several advantages by:

• Producing greater lift and permitting lower landing speed.

• Producing greater drag, permitting a steep descent angle without airspeed increase.

• Reducing the length of the landing roll. METEOROLOGICAL INFORMATIONThe Nat...