N815EY

HISTORY OF FLIGHTOn September 1, 2018, about 1720 central daylight time, an experimental amateur-built JETEZ airplane, N815EY, was destroyed after an in-flight breakup and a subsequent impact with terrain near Covington Municipal Airport (M04), Covington, Tennessee. The airline transport pilot was fatally injured. The airplane was owned by the pilot and operated as a Title 14 Code of Federal Regulations Part 91 personal flight. Visual meteorological conditions prevailed at the time of the accident, and no flight plan was filed for the local flight.

According to a witness who routinely observed the accident airplane's flights and was familiar with the airplane's design, the purpose of the flight was for the accident airplane and another canard jet airplane based at M04 to fly together. The witness reported that the accident airplane departed runway 19 before the other airplane, climbed to an altitude of about 1,000 ft above ground level (agl), and then started a 270° descending right turn. He also reported that the airplane crossed over the middle of M04 at an altitude of about 200 ft agl and an estimated speed of 200 to 210 knots and in a level pitch and bank attitude. He further reported that, shortly after the airplane crossed the runway, he observed the left wing and winglet "oscillate" about five times and that the left wing then "exploded."

This witness subsequently observed pieces of the airplane falling, the airplane abruptly pitching up about 90°, the right wing separating from the fuselage, and the airplane descending into a cotton field. He reported that the airplane's engine "sounded fine" throughout the flight. The witness provided an additional statement about 3 months after the accident, indicating that the airplane was traveling "at least 200 knots, it could have been 230 knots" just before the left wing failure.

According to another witness, who was an airline transport pilot, he observed the accident airplane cross over the airport at an altitude of about 200 ft agl. He stated the airplane's engine sounded as if it "was not at idle" and "had power." This witness continued watching the accident airplane after it flew over the airport and observed a "gentle pull-up" followed by a "wave like movement" or "wiggle" in the left wing, and then the "left wing failed at mid-span." Subsequently, the airplane pitched up "violently," the right wing "snapped off" in one piece, and several additional pieces departed the airplane as it "tumbled down to the left" and impacted terrain. He then observed fire and smoke. PERSONNEL INFORMATIONAccording to Federal Aviation Administration (FAA) records, the pilot held an airline transport pilot certificate with an airplane multiengine land rating and a commercial pilot certificate with airplane single-engine land and lighter-than-air balloon ratings. He also held a flight instructor certificate for airplane single- and multiengine land; and type ratings for the Airbus A320, Jetstream BA-3100, Embraer EMB-120, and Saab SF-340; and a repairman experimental aircraft builder certificate for the accident airplane as well as the DR-107 experimental amateur-built airplane.

The pilot was issued an FAA first-class medical certificate dated March 22, 2018, with a limitation that required him to wear corrective lenses. At that time, the pilot reported 22,000 hours of total flight experience, including 5 hours during the preceding 6 months. The pilot's logbooks were not recovered. AIRCRAFT INFORMATIONAccording to FAA airworthiness records and publicly available information, the airplane was a two-seat, original-design, canard-style airplane manufactured by the pilot. The airplane was powered by a modified GE-T58-8B turbine engine, which was originally designed for a military helicopter. The airplane received a special airworthiness certificate on June 30, 2014. The witness who was familiar with the operation of the accident airplane reported that it had accumulated about 100 total hours of operation. The maintenance records and builder records were not located. Extensive online content described how the accident pilot designed, manufactured, and operated the airplane.

In May 2018, KITPLANES magazine published an article authored by the accident pilot that was titled, "JET EZE, Turning a Dream into Reality, Part 1 and 2." The article included a photograph of the accident airplane at an unknown date and time before the accident flight, as shown in figure 1.

Figure 1. Accident airplane. (Source: KITPLANES magazine, May 2018.)

According to the article, the airplane was designed and manufactured over a 13-year period, with 11 years of "active building." The airplane had blended composite winglets in which a C-channel wing spar was extended to the tip of the winglets. The article stated that 5-ft peel ply was used in the composite layup process of the winglets. The article also stated that the canard was a "stock GU" design and that each wing contained two inner fuel pods and two outer baggage pods.

In February 2018, the accident pilot described the design, manufacture, and operation of the accident airplane in a narrated webinar titled "So, You Want to Build a Jet?" that was hosted by the Experimental Aircraft Association. A recording of the webinar appeared on the Jet Guys' YouTube channel (https://www.youtube.com/watch?v=_Izm3CGZDFo).

According to the "Jet Guys" website, they specialized in canard jet airframe modifications, repairs, powerplants, electrical modifications, and condition inspections. The owner and operator of Jet Guys was a witness to the accident (his account was provided first in this report). He was also the FAA designated airworthiness representative that signed off the airplane's special airworthiness certificate in 2014.

During the 1 hour 27-minute webinar, the pilot reported that the accident airplane had a Vne (never exceed airspeed) of 250 knots indicated airspeed (KIAS), or 310 knots true airspeed, and stated, "Have I been past that [airspeed]? Yeah, it was exciting, and I won't tell you how far I went past it." He explained that the airplane was "airframe limited" because the jet engine could propel the wings faster to loads that they could not tolerate. He also reported that the airplane's first flight was in 2017, although the airplane had received its FAA special airworthiness certificate in June 2014. METEOROLOGICAL INFORMATIONThe weather conditions reported at M04 at 1715 included visibility of 10 statute miles, few clouds at 5,000 and 5,500 ft agl, wind from 130° at 6 knots, temperature 31°C, and dew point 23°C. AIRPORT INFORMATIONAccording to FAA airworthiness records and publicly available information, the airplane was a two-seat, original-design, canard-style airplane manufactured by the pilot. The airplane was powered by a modified GE-T58-8B turbine engine, which was originally designed for a military helicopter. The airplane received a special airworthiness certificate on June 30, 2014. The witness who was familiar with the operation of the accident airplane reported that it had accumulated about 100 total hours of operation. The maintenance records and builder records were not located. Extensive online content described how the accident pilot designed, manufactured, and operated the airplane.

In May 2018, KITPLANES magazine published an article authored by the accident pilot that was titled, "JET EZE, Turning a Dream into Reality, Part 1 and 2." The article included a photograph of the accident airplane at an unknown date and time before the accident flight, as shown in figure 1.

Figure 1. Accident airplane. (Source: KITPLANES magazine, May 2018.)

According to the article, the airplane was designed and manufactured over a 13-year period, with 11 years of "active building." The airplane had blended composite winglets in which a C-channel wing spar was extended to the tip of the winglets. The article stated that 5-ft peel ply was used in the composite layup process of the winglets. The article also stated that the canard was a "stock GU" design and that each wing contained two inner fuel pods and two outer baggage pods.

In February 2018, the accident pilot described the design, manufacture, and operation of the accident airplane in a narrated webinar titled "So, You Want to Build a Jet?" that was hosted by the Experimental Aircraft Association. A recording of the webinar appeared on the Jet Guys' YouTube channel (https://www.youtube.com/watch?v=_Izm3CGZDFo).

According to the "Jet Guys" website, they specialized in canard jet airframe modifications, repairs, powerplants, electrical modifications, and condition inspections. The owner and operator of Jet Guys was a witness to the accident (his account was provided first in this report). He was also the FAA designated airworthiness representative that signed off the airplane's special airworthiness certificate in 2014.

During the 1 hour 27-minute webinar, the pilot reported that the accident airplane had a Vne (never exceed airspeed) of 250 knots indicated airspeed (KIAS), or 310 knots true airspeed, and stated, "Have I been past that [airspeed]? Yeah, it was exciting, and I won't tell you how far I went past it." He explained that the airplane was "airframe limited" because the jet engine could propel the wings faster to loads that they could not tolerate. He also reported that the airplane's first flight was in 2017, although the airplane had received its FAA special airworthiness certificate in June 2014. WRECKAGE AND IMPACT INFORMATIONThe airplane's fuselage came to rest inverted in a flat cotton field about 0.5 nautical mile northeast of M04. The fuselage was oriented on a magnetic heading of 065°. The airplane sustained extensive impact damage, and evidence of a postimpact fire was observed. All major components of the airplane were accounted for along the airplane's debris path. Fragments of the outboard portion of the left wing and winglet were found separate...