N602TF

HISTORY OF FLIGHTOn December 31, 2019, about 1606 central standard time, a Mooney M20S airplane, N602TF, was destroyed when it was involved in an accident near Olathe, Kansas. The pilot and the passenger were fatally injured. The airplane was operated as a Title 14 Code of Federal Regulations Part 91 personal flight.

A witness reported that he observed the accident at Johnson County Executive Airport (OJC), Olathe, Kansas. He said the accident pilot and a passenger flew in from Little Rock, Arkansas, to view an airplane that was for sale. The witness saw the pilot before he took off and observed “nothing out of the ordinary” regarding the pilot’s behavior and “no red flags” with respect to the pilot’s actions. The witness watched them take off for a return flight to their home base; he did not notice anything out of the ordinary on the airplane’s initial rollout. He indicated that, during the engine power-up, “all” sounded and looked normal. However, he noticed that the airplane rotated at a much slower speed than would be expected and immediately started to climb at a very high pitch attitude. The witness reported that as the airplane gained altitude, it appeared to fly slower to the point that the left wing stalled, “causing the [air]plane to nose over and continue its trajectory straight into the ground just east of the runway.” The witness stated that the engine power was “on” throughout the entire flight with no odd sounds noted.

A review of videos taken near the accident site was consistent with the witness statement regarding the flight. The airplane did not exhibit any in-flight fire or smoke in the videos, and a ground fire was observed after impact.

Data extracted from the JPI EDM 800 engine recorder appeared to be consistent with the accident flight. The data showed engine operation consistent with taxi, before takeoff checklist items, and takeoff. The data showed the engine operation was consistent with a full power application until the data stopped.

PERSONNEL INFORMATIONAccording to a flight instructor, the pilot was given instruction in the Mooney to include basic maneuvers, takeoffs, landings, airport entry activities, cross-country activities, and go-arounds. The pilot was given instruction in using an after landing checklist that included setting flap, mixture switches, and trim for takeoff. He characterized the pilot as a “quick learn” and an “excellent student.” The instruction totaled 6.8 hours of flight time.

AIRCRAFT INFORMATIONA review of Federal Aviation Administration (FAA) records showed the pilot and a co-owner purchased the airplane on November 26, 2019. The airplane did not receive any fuel at OJC.

According to the pilot operating handbook, the entire empennage pivots around its main hinge points to provide pitch trim control. The system consists of a manually operated actuator that operates a series of torque tubes and universal joints connected to a jack screw on the aft tailcone bulkhead. A trim control wheel, located between the pilot and copilot seats, allows the pilot to set the stabilizer trim angle. Trim position is indicated by an electrical gauge located in the center flight panel. This indicates the stabilizer position relative to the aircraft thrust line. The before takeoff checklist stated, in part, “Elevator Trim ... TAKEOFF SETTING.”

Mooney issued Service Bulletins (SB) M20-313A, “Empennage Trim Fitting And Mounting Hardware Inspection,” and M20-314A, “Empennage Trim Fitting And Mounting Hardware Replacement Instructions,” on February 29, 2012, to require a one-time inspection to ensure the trim filler plate is positioned correctly with the trim fitting and trim hinge. SB M20-314A listed compliance as mandatory, before the next flight.

On March 20, 2012, the FAA issued Airworthiness Directive (AD) 2012-05-09, which required inspecting the trim fitting, hinge, and filler plate of the tail pitch trim assembly for correct positioning and proper attachment, and inspecting the Huck Bolt fasteners for proper security on all Mooney models, including the accident airplane. The AD was prompted by a report of an incident on a Mooney M20TN airplane regarding failure of the tail pitch trim assembly, which could result in a loss of control, and the potential for this condition to exist on other airplane models.

A mechanic who had worked on the accident airplane was advised that the airplane logbooks were not located and was asked if the SBs and AD had been accomplished. He stated, in part, that those items were not shown on the work order but would have shown on the AD list. He indicated that “it is a normal part” of the annual checklist and that he was sure it was complied with previously or it would have been listed on the work order as an action item.

AIRPORT INFORMATIONA review of Federal Aviation Administration (FAA) records showed the pilot and a co-owner purchased the airplane on November 26, 2019. The airplane did not receive any fuel at OJC.

According to the pilot operating handbook, the entire empennage pivots around its main hinge points to provide pitch trim control. The system consists of a manually operated actuator that operates a series of torque tubes and universal joints connected to a jack screw on the aft tailcone bulkhead. A trim control wheel, located between the pilot and copilot seats, allows the pilot to set the stabilizer trim angle. Trim position is indicated by an electrical gauge located in the center flight panel. This indicates the stabilizer position relative to the aircraft thrust line. The before takeoff checklist stated, in part, “Elevator Trim ... TAKEOFF SETTING.”

Mooney issued Service Bulletins (SB) M20-313A, “Empennage Trim Fitting And Mounting Hardware Inspection,” and M20-314A, “Empennage Trim Fitting And Mounting Hardware Replacement Instructions,” on February 29, 2012, to require a one-time inspection to ensure the trim filler plate is positioned correctly with the trim fitting and trim hinge. SB M20-314A listed compliance as mandatory, before the next flight.

On March 20, 2012, the FAA issued Airworthiness Directive (AD) 2012-05-09, which required inspecting the trim fitting, hinge, and filler plate of the tail pitch trim assembly for correct positioning and proper attachment, and inspecting the Huck Bolt fasteners for proper security on all Mooney models, including the accident airplane. The AD was prompted by a report of an incident on a Mooney M20TN airplane regarding failure of the tail pitch trim assembly, which could result in a loss of control, and the potential for this condition to exist on other airplane models.

A mechanic who had worked on the accident airplane was advised that the airplane logbooks were not located and was asked if the SBs and AD had been accomplished. He stated, in part, that those items were not shown on the work order but would have shown on the AD list. He indicated that “it is a normal part” of the annual checklist and that he was sure it was complied with previously or it would have been listed on the work order as an action item.

WRECKAGE AND IMPACT INFORMATIONThe wreckage was oriented about 171° and about 2,550 ft from the departure threshold of runway 18. Major components of the airplane were identified at the accident site. The top of the fuselage was consumed by fire between the instrument panel to just forward of the empennage. The lower section of the fuselage was discolored, deformed, and melted. The engine compartment exhibited aft migration of the engine against the firewall. The propeller was embedded in terrain; examination after recovery revealed “S”-shaped bending and leading-edge nicks. The empennage and fuselage aft of the cabin were bent laterally toward the left wing about 30°. The leading edge of the right wing exhibited aft crushing. The leading edge of the left wing exhibited discoloration, melting, and deformation. The position of the left main landing gear could not be determined due to the left wing’s thermal damage. The right main landing gear was found partially extended. Flight control continuity from all the flight control surfaces to the cabin area was traced. The ignition key switch was set to the BOTH position. The mixture, propeller, and throttle control knobs were in their forward positions. Examination of the engine compartment confirmed control continuity of the mixture, propeller, and throttle controls from their engine accessories to their respective cockpit controls. The airplane instrument panel was damaged by impact forces and thermal damage. The JP Instrument (JPI) EDM 800 unit exhibited impact and thermal damage and was shipped to the National Transportation Safety Board (NTSB) Recorder Laboratory to determine if it contained data in reference to the accident flight. Data with respect to 7 engine parameters, time, outside air temperature, and electrical bus voltage, was extracted and included 12 sessions with the final session determined to be related to the accident flight.

An engine disassembly examination was conducted. There were no preimpact anomalies detected during the examination that would have precluded normal operation.

A fixed-base operator that services Mooney airplanes supplied photographs of an exemplar trim system jack screw at takeoff and full up trim settings; when the trim indicator was in the full up position, the jack screw was at its full extension. A postaccident photograph of the accident airplane’s trim jack screw was consistent with the full up trim setting in the exemplar photographs.

MEDICAL AND PATHOLOGICAL INFORMATIONAccording to the FAA medical certification file and FAA medical case review, at the time of the pilot’s most recent FAA medical certification examination on May 28, 2019; he reported taking no medications and having a history of seasonal allergies. No significant medical concerns or issues were identified.

According to the Forensic Medical of Kansas, LLC, Kansas City, Kansas, autop...