N7463W

On August 19, 2023, about 1800 eastern daylight time, a Piper PA28-180, N7463W, was substantially damaged when it was involved in accident near Preston, Connecticut. The pilot and passenger were not injured. The airplane was operated as a Title 14 Code of Federal Regulations Part 91 personal flight.

According to the pilot, he departed Martha’s Vineyard Airport (MVY), Vineyard Haven, Massachusetts, and was destined for Groton-New London Airport (GON), Groton, Connecticut. Once he reached a cruise altitude of 4,500 ft mean sea level, he noticed the oil pressure gauge indication drop to zero. Seconds later, he noticed oil pouring out of the engine cowling and flowing up the windscreen. The engine then lost total power. The pilot tried to glide the airplane to GON but was unable to reach the runway, so he set up for a landing in a field. The pilot successfully landed the airplane in the field but, during the landing rollout, the right wing struck a metal pipe that was hidden in brush. The airplane rotated 180° and the right wing separated from the fuselage, resulting in substantial damage.

An examination of the engine revealed that the left side of the engine case was ruptured and fragments of the engine case were sitting on top of the engine.

Further examination of the engine revealed the portion of the left crankcase half above the No. 2 cylinder was fractured and separated from the engine. The crankshaft end of the No. 2 connecting rod was separated from the crankshaft’s No. 2 rod journal. The rod was deformed consistent with battering the rod journal and the interior of the right crankcase half. One portion of the rod, including a rod bolt hole, was bent inward. There was no rod bolt in the hole. A bent portion of a rod bolt with a nut still installed was recovered from the interior of the crankcase. A portion of the rod cap with the head portion of the rod bolt still in place was also recovered from the crankcase. The other portion of the connecting rod and the corresponding half of the rod cap and the rod bolt were separated from the rod and not recovered. Thin ferrous material, consistent with remnants of the No. 2 bearing was also recovered from the crankcase and the oil sump. The No. 2 cylinder was removed and the crankshaft rotated by turning the crankshaft propeller flange. Continuity of the crankshaft to the rear gears and to the valvetrain of cylinders Nos.1, 3, and 4 was confirmed. Compression and suction were observed from cylinders Nos. 1, 3, and 4.

A review of the airplane’s maintenance logs revealed that the most recent engine overhaul was completed on October 1, 1998. According to a log entry dated June 20, 2007, the engine was disassembled and inspected due to “metal contamination.” The maintenance log entry for this work noted, in part, the installation of “new main and rod bearings.”

An entry dated June 1, 2022 documented an annual inspection and noted that the oil and oil filter were replaced, but did not document whether the old filter was cut open and inspected for contamination. The entry also indicated that cylinder compressions were: No. 1 80 psi, No. 2 42 psi, No. 3 75 psi, No. 4 42 psi. No corrective actions were noted in the entry.

An entry dated May 12, 2023, indicated that the tachometer (airframe/engine total time) was 3,500.5 hours, the engine time since major overhaul was 939.5 hours, and the time since the 2007 disassembly of the engine was 631.5 hours. The entry documented that the oil was changed, that the oil filter was replaced, and that the previous oil filter was cut open and examined with “no contaminants found.” The entry noted that the cylinder compressions were: No. 1 74 psi, No. 2 22 psi, No. 3 70 psi, No.4 35 psi. It also stated, “Lap exhaust valves on cylinders #2 and #4. Recommend retest in 10 hours.”

Lycoming Service Instruction No. 1191A stated: “If the pressure reading for all cylinders is equal and above 70 psi; the engine is satisfactory; less than 65 psi indicates wear has occurred and subsequent compression checks should be made at 100-hour intervals to determine rate and amount of wear. If the pressure reading is below 60 psi or if the wear rate increases rapidly, as indicated by appreciable decrease in cylinder pressure, removal and overhaul of the cylinders should be considered.”

According to Lycoming Service Instruction No. 1009BE, “All engine models are to be overhauled within twelve (12) calendar years of the date they first entered service or of last overhaul. This calendar year time period TBO is to mitigate engine deterioration that occurs with age, including corrosion of metallic components and degradation of non-metallic components such as gaskets, seals, flexible hoses and fuel pump diaphragms.”