N89FB

HISTORY OF FLIGHT

On August 1, 2001, at 1300 eastern daylight time, a Bell 206B helicopter, N89FB, operated by Helicopter Transport Services, was destroyed during collision with terrain at the Baltimore-Washington International Airport (BWI), Baltimore, Maryland. The helicopter came to rest on the Alpha taxiway abeam runway 15 Right. The certificated commercial pilot and photographer/passenger were fatally injured. Visual meteorological conditions prevailed for the aerial photography flight that originated at the Martin State Airport (MTN), Baltimore, Maryland, at 1232. No flight plan was filed for the flight conducted under 14 CFR Part 91.

According to the operator, the purpose of the flight was to take aerial photographs of a large airport expansion construction project at BWI.

During an interview, one witness said he was facing in a northwesterly direction as he observed the helicopter flying overhead. He said the helicopter did a succession of 180-degree turns that increased in rate of rotation.

According to the witness, the helicopter approached from the east at hover-taxi speed. He said the helicopter hovered over his head and turned to the north, which oriented the tail of the helicopter into the wind. The witness said the helicopter came to a stationary hover, about 400 feet above the ground, with a direct tailwind.

Once at a hover, the helicopter did a rapid 180-degree pedal turn around the mast, stopped momentarily, then initiated another rapid pedal turn to the right. According to the witness, the helicopter turned at a faster rate than the initial turn, and continued into a descending turn "spinning clockwise, to the right."

With a model of a helicopter in his hand, the witness demonstrated the nose of the helicopter initiating a turn to the right and then continuing a slow spiraling descent to the right. When questioned about the helicopter's engine noise, the witness said:

"I didn't hear anything that was abnormal or out of the ordinary. It sounded like he wasn't having any trouble. There was nothing out of the ordinary. I didn't see any smoke, or parts, or debris."

A second witness said he was standing inside the construction site, and viewed the helicopter as he faced the northwest. According to the witness, the helicopter flew slowly around the construction site. He said his attention was drawn to the helicopter because he felt it was unusual for the helicopter to be at a hover less than 500 feet above the ground.

With a model of a helicopter in his hand, the witness described what he saw and maneuvered the model at the same time. He showed the nose of the helicopter pointed to the north, and said the helicopter was at a stationary hover. The witness demonstrated a jerking of the nose to the right, turns around the mast, and then a spiraling descent.

The witness said the helicopter was running "fine", and said the pilot made rapid hand and arm movements inside the cockpit during the descent.

A third witness was interviewed at the Martin State Airport on the day after the accident. The witness said he was flying a Bell 206B helicopter in the vicinity of BWI Airport at the time of the accident, and then over the airport immediately following to film for a local news station.

The witness went on to describe his flight over the airport, and the winds he encountered aloft. He said the winds were out of the south-southeast and that they were very unstable. The witness said his helicopter would experience an updraft, a good strong downdraft, no wind, and then a strong wind. While in a stationary out-of-ground-effect hover at 1,000 feet, the airspeed indicator showed 20 knots. He said the airspeed indicator would drop to zero and the helicopter would descend and shake violently. According to the witness:

"One minute the winds were from 150 to 180 degrees and then from 240 degrees. If you were in a position where you were flying downwind, it was an ideal situation for LTE (loss of tail rotor effectiveness)."

The accident occurred during the hours of daylight approximately 39 degrees, 10 minutes north latitude, and 076 degrees, 40 minutes west longitude.

PERSONNEL INFORMATION

The pilot held a commercial pilot certificate with a rating for rotorcraft/helicopter. He also held a private pilot certificate with a rating for airplane single engine land. The pilot did not posses an instrument rating.

The pilot's logbook was not recovered. A review of the pilot's company flight records revealed he had 531 hours of total flight experience, 60 hours of which were in airplanes. The pilot had 87.2 hours of experience in the Bell 206B, and 72 hours in the Bell 206L.

The pilot's most recent biennial flight review was completed in conjunction with a Part 135 evaluation on July 11, 2001. The purpose of the evaluation was so that he could perform Part 135 operations for his employer.

Further review of the pilot's flight records revealed that he completed the "Bell Helicopter OH-58 Ground and Flight Procedures Training Course" on August 16, 1996. The course included 3.9 hours of flight time. The pilot received a total of 3.7 hours of instruction in the Bell 206 from the operator's chief pilot. The most recent training flight was completed June 28, 2001, and was 2 hours in duration.

The pilot's most recent Federal Aviation Administration (FAA) second-class medical certificate was issued on June 19, 2001.

AIRCRAFT INFORMATION

Examination of the maintenance records revealed the helicopter was on an annual inspection program. The most recent inspection was a 100-hour inspection that was completed October 23, 2000, at 10,883 aircraft hours. The helicopter had accrued 66.4 hours since that date.

METEOROLOGICAL INFORMATION

At 1254, the weather reported at the Baltimore-Washington International Airport included few clouds at 5,000 feet with variable winds at 6 knots. At 1249:54, air traffic control (ATC) advised landing traffic that the winds were from 130 degrees at 6 knots. At 1253, ATC advised landing traffic that the winds were from 140 degrees at 8 knots.

WRECKAGE AND IMPACT INFORMATION

The helicopter was examined at the site on August 1, 2001, and all major components were accounted for at the scene. The helicopter came to rest upright on taxiway Alpha, north of runway 15 Right. The helicopter came to rest at the initial point of ground contact oriented 150 degrees magnetic.

The skid tubes were fractured into three pieces each, and scattered beyond the nose of the helicopter. The cross tubes collapsed forward, and were pinned beneath the wreckage. The fuselage was crushed upwards in compression.

Examination of the cockpit area revealed the pilot's cyclic control stick was broken off about 6 inches below the cyclic grip. The collective stick was intact, but separated from the collective jackshaft. The pilot's tail rotor pedals were intact, but the interconnect push/pull tube was fractured 2 inches from the mixing unit bearing clevis.

Rescue personnel cut the pilot's windshield post. The pilot's side doorpost was fractured in compression.

The flight control "broom closet", situated vertically between the pilot and copilot seats, was crushed upwards, and the cyclic and collective mixing units were exposed.

The floor of the helicopter was crushed upwards and displaced slightly to the left. The empennage was crushed upwards and wrinkled back to the tailboom. The engine deck was wrinkled and deformed. The isolation mount plate, directly beneath the main drive shaft transmission input coupling, displayed a concave dent the approximate size of the coupling. There was rotational smearing across the entire radius of the dent.

Examination of the fuel control quadrant revealed the quadrant pointer was at the 90-degree full-open position.

The aluminum particle separator baffling above the main drive shaft transmission input coupling was punctured and the aluminum was torn and displayed rotational smearing. The puncture was approximately the same width as the input coupling and directly forward of the engine air inlet.

The main drive shaft was still attached at both the engine and transmission. The shaft was displaced upward in the transmission input coupling, and coupling grease was ejected around the transmission pylon area.

The #1 tail rotor drive shaft was fractured 18 inches aft of the tail rotor drive shaft output quill of the engine accessory case. The fracture was directly below a puncture in the engine combustor. The fracture surfaces appeared torn, and the torn metal was wrapped circumferentially. At a point aft of the break, the tail rotor drive shaft was rotated by hand. The tail rotor rotated freely, with no binding noted in the hanger bearings or the 90-degree gearbox.

The tailboom was intact from the empennage back to the vertical fin attach points. Both horizontal stabilizers were intact. The lower half of the vertical stabilizer was crushed upwards about 18 inches.

The tailrotor blades were marked "target" and "blank", respectively. Both blades displayed impact damage and chordwise scratching at the tips. Both blades were wrinkled at mid span. The blank blade was bent over about 90 degrees at a point approximately 6 inches from the hub and rested on the ground.

Both main rotor blades displayed chordwise scratching and upward bending on the trailing edge. Both blades displayed chordwise scoring through the blade skin, at a point approximately 4.5 feet from the blade grip. Rotation of the main rotor blades revealed the score marks were aligned approximately over top of the upper Wire Strike Protection System (WSPS) cutter. The cutter was bent and displaced to the left.

Rotation of the main rotor blades also established continuity through the transmission to the main drive shaft input coupling with no binding.

Collective, cyclic, and tail rotor control continuity could not be established at the scene.

The heli...