N4955A

HISTORY OF FLIGHT

On May 27, 2011, about 1014 Alaska daylight time, a Cessna 180, N4955A, collided with terrain after a loss of control during the initial climb after takeoff from the Birchwood Airport, Chugiak, Alaska. The airplane received substantial damage as a result of the impact and a postcrash fire. The airplane was registered to the pilot, and operated under the provisions of 14 Code of Federal Regulations (CFR) Part 91 as a personal cross-country flight. Visual meteorological conditions prevailed at the time of the accident. The certificated private pilot and the four passengers were killed. The flight was originating at the time of the accident and was en route to Seldovia, Alaska.

Several witnesses stated that they saw the accident airplane takeoff from runway 19R in a very nose high attitude. One witness stated that the airplane went off of the left side of the runway before becoming airborne, headed toward a row of trees on the east side of the airport. The airplane climbed over the trees, turned to the south, then rolled right and descended into the ground. The witnesses said that the engine sounded like it was running at full power.

During a telephone interview, a personal acquaintance of the accident pilot told the NTSB investigator-in-charge (IIC), that the family was building a cabin in Seldovia, and he thought that this was the first trip of the year for the pilot. Another acquaintance stated that he had flown the accident airplane with the accident pilot in May 2010. During that flight he said the accident pilot almost stalled the airplane on takeoff, and after the flight he had told him that he shouldn’t try and fly the airplane by himself, and should get additional flight training in the airplane.

PERSONNEL INFORMATION

The pilot, age 46, held a private pilot certificate with a rating for airplane single engine land. He was issued a third class airman medical certificate without limitations on May 6, 2010.

The pilot’s flight logbook was examined by the NTSB IIC. The logbook covered the period from April 4, 1982, through June 12, 2010, and indicated that he had logged 198.9 hours total time, and 3.7 hours in a Cessna 180. Between June 10, 2010 and June 12, 2010, the pilot received instruction in the Cessna 180, and completed the requirements of a flight review. He also received endorsements for acting as pilot in command of a tailwheel airplane as well as a high performance airplane. There were no entries after June 12, 2010.

AIRCRAFT INFORMATION

The accident airplane was equipped with a Continental Motors O-470-K engine, rated at 230 horsepower at 2,600 rpm. The engine was equipped with a two-blade McCauley propeller.

At the time of its last annual inspection, May 1, 2010, the airplane and engine had 4,908 service hours. The last annual inspection prior to the 2010 inspection was completed on December 7, 2000, at 4,906.4 service hours. The tachometer was found at the accident site; however, damage precluded determining the current reading.

The engine had a major overhaul on June 2, 1994, and was operated about 240 hours before the accident.

The most recent official weight and balance documentation was not located in the airplane records.

METEOROLOGICAL INFORMATION

The closest official weather observation station is Birchwood, Alaska. At 1016, an aviation routine weather report (METAR) was reporting, in part: Wind 250 degrees (true) at 4 knots; visibility 10 statute miles; sky condition, clear; temperature 55 degrees F; dew point, 39 degrees F; altimeter 29.86 inHg.

WRECKAGE AND IMPACT INFORMATION

On May 27, 2011, the NTSB IIC, along with another NTSB investigator, and an FAA operations inspector from the Anchorage Flight Standards District Office (FSDO), examined the airplane wreckage at the accident site.

The airplane collided with terrain in a rail yard approximately 700 yards southeast of the departure end of runway 19 right. The main wreckage came to rest upright, on an approximate heading of 050 degrees magnetic. The point of initial impact was determined to be a series of propeller strike marks, and pieces of fiberglass from the right wingtip, approximately 45 feet from the main wreckage. All of the airplane’s major components were at the main wreckage site.

The majority of the fuselage was consumed by a postcrash fire. The right wing was crushed aft and bent upward to approximately mid-span, and had extensive fire damage over the entire span. The left wing showed leading edge damage near the wingtip, and the inboard half of the wing had fire damage. The empennage was mostly free of impact and fire damage from the front of the vertical stabilizer aft. The tailwheel assembly was broken and displaced upward from its mounts.

Due to impact and fire damage, the flight controls could not be moved by their respective control mechanisms, but continuity of the flight control cables was established to the cockpit area.

The engine remained connected to the engine mounts and was extensively damaged by the postcrash fire. The propeller assembly remained connected to the engine and showed extensive impact and fire damage. Both propeller blades remained attached to the propeller hub, but both were loose in the hub. One propeller blade was bent aft from the mid section approximately 130 degrees, showed leading edge gouging, and approximately 5 to 10 inches of the outboard blade was separated. The opposite propeller exhibited torsional twisting, leading edge gouging, and approximately 3 to 5 inches of the outboard blade was separated. One of the separated sections of propeller blade was heavily gouged, bent, and splintered. The other separated portion of propeller was gouged and showed chord-wise scratching.

The runway the accident airplane departed from had a set of tire marks that were observed in the area that witnesses stated the airplane departed the runway. The tire marks showed a curved path leading from the edge of the left side of the runway, through the dirt, to a point approximately halfway between runway 19 right and runway 19 left.

MEDICAL AND PATHOLOGICAL INFORMATION

A postmortem examination of the pilot was done under the authority of the Alaska State Medical Examiner, Anchorage, Alaska, on May 31, 2011. The examination revealed that the cause of death was attributed to severe thermal charring, in addition to severe blunt force injuries.

A toxicological examination by the FAA’s Civil Aeromedical Institute (CAMI) on June 27, 2011, was negative for any alcohol or drugs.

TESTS AND RESEARCH

On May 31, the NTSB IIC, along with representatives of the FAA, Cessna Aircraft Company, and Continental Motors, revisited the accident site to further document the airplane and its components.

Airframe

The horizontal stabilizer trim setting was measured at 7.6 inches, which equates to minus 5 degrees. According to Cessna aircraft, the normal takeoff trim position is minus 3.5 degrees. The stabilizer trim setting range is from positive 1.5 degrees to minus 8.5 degrees.

The fuel selector valve was found to be in the right main tank position.

Seats Track Rails

The two front seats are individually mounted on set of tracks, and each seat is individually adjustable, forward and aft. A seat adjustment handle is located on the left side of each seat. When the seat adjustment handle is raised, it disengages a spring-loaded locking pin from 1 of 17 holes situated on the top of the left side seat track rail. Once the locking pin is disengaged, the seat is free to roll forward or backward on a set of 4 rollers.

On September 24, 1990, the FAA issued a revised Airworthiness Directive (AD) 87-20-03 R2, which defines the airworthiness requirements and minimum acceptable wear limits on the seat locking mechanism and seat track components. The AD states, in part: "...If the wear dimension across any hole exceeds 0.36 inches but does not exceed 0.42 inches, continue to measure each hole every 100 hours for excessive wear. ...If the wear dimension across any hole exceeds 0.42 inches, prior to further flight, replace the seat track."

On May 14, 2007, Cessna Aircraft Company issued service bulletin SEB07-5, which provides for the installation of a secondary seat stop kit for the pilot seat. The service bulletin states, in part: "The secondary seat stop is designed to assist in providing an additional margin of safety by limiting the aft travel of the seat in the event the primary latch pin is not properly engaged in the seat rail/track. In certain instances, seat slippage could result in some pilots not being able to reach all the controls and/or subsequently losing control of the airplane. Compliance is mandatory: Shall be accomplished within the next 200 hours of operation or 12 months, whichever occurs first." Installation of the Cessna secondary seat stop inertial reel kit (SK 210-147A) is required to comply with the service bulletin.

The airplane logbooks indicate that the Cessna secondary seat stop inertial reel kit (SK 210-174A) was installed, and the airworthiness directive (AD 87-20-03 R2) for seat track inspection was complied with, at the last annual inspection (May 1, 2010).

The rear leg of the pilot’s seat was found melted into the seat rail, in a position approximately 22 inches forward of the aft end of the seat rail. This equates to a seat location that would be in the first or second most forward seat position. The seat latch pin on the pilot’s seat was bent forward approximately 20 degrees. The left outboard seat track had a seat stop installed, and the right inboard seat track also had a seat stop installed.

There was no evidence of seat slippage with the pilot’s seat.

Control locks

The airplane was delivered with a cabin type control gust lock device, which connects to the control yoke, rudder pedals, and the floor of the airplane. There was no evidence that the control gust lock was installed in the airplane at the time of the accident. The airplane was not eq...