N804ST

HISTORY OF FLIGHTOn May 23, 2016, about 2156 central daylight time, a Cessna 501, N804ST, lost cabin pressurization during cruise at flight level (FL) 430 and entered an uncontrolled descent near Texarkana, Arkansas. The pilot regained consciousness and control of the airplane. The pilot landed the airplane without further incident at Texarkana Regional Airport-Webb Field (TXK), Texarkana, Arkansas. The airplane sustained substantial damage to both wings due to the excessive aerodynamic loads on the wings during the descent/recovery. The airline transport pilot and two passengers sustained minor injuries and one passenger was uninjured. The airplane was registered to and operated by Eagle II Aero LLC under 14 Code of Federal Regulations Part 91 as an executive/corporate flight that was operating on an instrument flight rules (IFR) flight plan. Night meteorological conditions prevailed at the time of the accident. The flight last departed from Perryville Municipal Airport, Perryville, Missouri (K02), about 2056, and was destined to San Antonio International Airport (SAT), San Antonio, Texas.

The airplane was flown by a single-pilot for the accident flight. According to air traffic control (ATC) radio communications, N804ST made initial contact with Memphis Center at 2056, after departing K02, to report climbing through 9,200 feet with an IFR flight plan on file. N804ST responded to all ATC transmissions while climbing to and leveling off at flight level 430, which was an altitude that was above reported cloud tops at FL 390. At 2154, Fort Worth Center called N804ST, but there was no response from N804ST. At 2155, Fort Worth Center attempted to contact N804ST three times and issued the Fort Smith altimeter. Fort Worth Center contacted Memphis Center and advised that N804ST had an "issue" and was descending. At 2156, Memphis Center instructed American Airlines flight 93 (AAL93) to attempt to contact N804ST on guard frequency. Fort Worth Center asked N804ST to IDENT; N804ST reported an explosive decompression. Fort Worth Center advised Memphis Center that they were now communicating with N804ST. At 2157, AAL93 advised Memphis Center that they were unable to contact N804ST on guard frequency. N804ST reported that the airplane was under control and would level off shortly. Fort Worth Center asked whether N804ST would like to fly to TKX or Fort Smith Regional Airport (FSM), Fort Smith, Arkansas. At 2148, the pilot of N804ST asked for a few minutes to "figure this out" and then advised he would like to land at TKX. Memphis Center advised that N804ST was located 12 o'clock and 35 miles from TKX. The pilot performed a visual approach and landing to runway 13 (5,200 by 100 feet, asphalt) at TXK, where the flight landed without further incident.

The pilot reported in a written statement that within 20 seconds, the airplane lost all cabin pressurization, and the cabin altitude climbed from 8,000 feet and 8.5 psi differential (psid) to ambient altitude and 0 psid. All the occupants lost consciousness. The pilot regained consciousness and control of the airplane at 7,000 feet.

According to the Federal Aviation Administration (FAA) coordinator for the accident, the pilot stated that he was not wearing an airplane supplemental oxygen system crew mask during the flight. PERSONNEL INFORMATIONThe pilot held an airline transport pilot certificate with the following type ratings: CE-500, CE-525, CE-650, MJ-300, BE-400, G-1159, DC-3, N-P51N, N-T28, T-33. On November 15, 2014, the pilot completed single-pilot exemption training including differences training for CE-500, CE-550, and CE-560 training. The pilot's last flight review was dated May 11, 2016, using a Beechcraft BE400. The pilot reported a total flight time of 15,000 hours, of which 5,000 hours were in the make and mode of the accident airplane. AIRCRAFT INFORMATIONThe airplane's type certificate, held by Textron Aviation Inc., shows that the Cessna 501 was certified under Part 23 with two Pratt & Whitney Aircraft of Canada, Ltd. JT15D-1A or JT15D-1B turbofan engines and had a maximum operating altitude of 41,000 feet.

The accident airplane was modified from its type design by supplemental type certificates (STCs), held by Sierra Industries Ltd., which increased the maximum operating altitude to 43,000 feet. The two STCs were:

SA732NW was for the installation of the Eagle SP performance system, including recontoured wing leading edge, wing tip extension, increased gross weight, increased fuel capacity, and other minor refinements.

ST09559AC was for the installation of Williams International Company. L.L.C. FJ44-2A engines in Cessna 501/500 aircraft or Williams International Company, L.L.C. FJ44-3A engines in Cessna Model 550/S550 aircraft. This STC increased the maximum operating altitude to 43,000 feet.

The Model 500 Maintenance Manual (Rev 39), Floor Panels – Inspection/Check called for the inspection of the air conditioning system in section D. Inspect Air Conditioning System: (1) Inspect all duct work and tubing for security of installation, evidence of damage or leakage, and (3) Inspect flapper check valves at air mixer assembly for ease of operation or evidence of binding.

The most recent maintenance inspection of the airplane was a Phase 5 inspection. A copy of the maintenance checklist used for the inspection, Model 500 Maintenance Manual (Rev 37) had the following entries: "Date:" - no entry made, "Registration Number: N804ST", "Serial Number: 501-0146", and "Total Time: 7424.8".

A Sierra Industries Ltd. Maintenance Transaction Report, dated April 15, 2016, stated, "Completed phase inspections in accordance with Cessna 500 maintenance manual chapter 5," at 7,424.8 aircraft hours, 6,411 landings, and no. 1 engine and no. 2 engine total hours were 846.8 hours and 539 cycles.

The Hobbs meter following the accident indicated 0411.3 hours.

The airplane oxygen system supplies breathing oxygen to the crew at all times and to the passengers when required. The pilot can manually drop the passenger masks by selecting manual drop on the oxygen control valve, or the passenger masks will automatically drop at 14,800 ±200 feet cabin altitude. The pilot can select crew only which will shutoff flow to the passengers. AIRPORT INFORMATIONThe airplane's type certificate, held by Textron Aviation Inc., shows that the Cessna 501 was certified under Part 23 with two Pratt & Whitney Aircraft of Canada, Ltd. JT15D-1A or JT15D-1B turbofan engines and had a maximum operating altitude of 41,000 feet.

The accident airplane was modified from its type design by supplemental type certificates (STCs), held by Sierra Industries Ltd., which increased the maximum operating altitude to 43,000 feet. The two STCs were:

SA732NW was for the installation of the Eagle SP performance system, including recontoured wing leading edge, wing tip extension, increased gross weight, increased fuel capacity, and other minor refinements.

ST09559AC was for the installation of Williams International Company. L.L.C. FJ44-2A engines in Cessna 501/500 aircraft or Williams International Company, L.L.C. FJ44-3A engines in Cessna Model 550/S550 aircraft. This STC increased the maximum operating altitude to 43,000 feet.

The Model 500 Maintenance Manual (Rev 39), Floor Panels – Inspection/Check called for the inspection of the air conditioning system in section D. Inspect Air Conditioning System: (1) Inspect all duct work and tubing for security of installation, evidence of damage or leakage, and (3) Inspect flapper check valves at air mixer assembly for ease of operation or evidence of binding.

The most recent maintenance inspection of the airplane was a Phase 5 inspection. A copy of the maintenance checklist used for the inspection, Model 500 Maintenance Manual (Rev 37) had the following entries: "Date:" - no entry made, "Registration Number: N804ST", "Serial Number: 501-0146", and "Total Time: 7424.8".

A Sierra Industries Ltd. Maintenance Transaction Report, dated April 15, 2016, stated, "Completed phase inspections in accordance with Cessna 500 maintenance manual chapter 5," at 7,424.8 aircraft hours, 6,411 landings, and no. 1 engine and no. 2 engine total hours were 846.8 hours and 539 cycles.

The Hobbs meter following the accident indicated 0411.3 hours.

The airplane oxygen system supplies breathing oxygen to the crew at all times and to the passengers when required. The pilot can manually drop the passenger masks by selecting manual drop on the oxygen control valve, or the passenger masks will automatically drop at 14,800 ±200 feet cabin altitude. The pilot can select crew only which will shutoff flow to the passengers. WRECKAGE AND IMPACT INFORMATIONPost-accident examination of the airplane by the FAA coordinator revealed that the cockpit supplemental oxygen supply gauge indicated about 17 "psi x100," which was in the gauge's green arc of 16-18 psi x100.

The cockpit supplemental oxygen system switch was in the "Normal" position (which would have provided oxygen to the cabin masks). The cabin oxygen masks were not deployed. The pilot stated to the FAA coordinator that the switch was in the "Crew" position, and he did not know how or why it was in the "Normal" position. The pilot later told the FAA coordinator that he changed the oxygen switch position after the accident.

The examination revealed that the aft pressure bulkhead check valve flapper had half of its non-metallic flapper fractured into several pieces, which were resting on the fuselage floor. The second half of the check valve flapper was intact in valve body. The air conditioning system's primary pressurization duct leading to the cabin was separated from its connection with the water separator. The duct's metal worm-gear retaining clamp was resting around the duct and away from its attachment point to the separator. The clamp's retaining screw was in place. The clamp was not fractured. The clamp, the check valve, and the flapper pie...