N846PM

HISTORY OF FLIGHT

On May 15, 2017, about 1644 Pacific daylight time, an experimental, amateur-built Lancair Evolution, N846PM, was substantially damaged when it was involved in an accident near Firebaugh, California. The front seat passenger and one rear seat passenger received minor injuries; the private pilot and two other passengers were uninjured. The airplane was operated as a Title 14 Code of Federal Regulations Part 91 personal flight.

The pilot reported that he and four family members departed on a cross-country flight to return to their home airport. While cruising at an altitude of 25,000 feet, the windshield suddenly "exploded." The airplane's cabin experienced an instant decompression, and the pilot activated the oxygen system and donned his oxygen mask. During the subsequent steep descent, the pilot located and navigated to a nearby airport. After he turned to the final leg of the airport traffic pattern, the pilot extended the landing gear but did not receive confirmation that the left main landing gear was extended and locked via the landing gear position indicator lights. After recycling the landing gear and receiving the same indication, the pilot decided to land with the landing gear retracted. He stated that, although the airplane made contact with the runway at high speed, the touchdown was smooth and level. The airplane overran the runway, impacted a fence, and continued across a road before it came to rest in a field, sustaining substantial damage to both wings.

The airplane came to rest in a field about 900 ft beyond the departure end of runway 12. All major components of the airplane were accounted for at the accident site. Most of the windshield was broken, with the exception of a few fragments that remained attached to the fuselage frame. Each of the engine's four propeller blades was bent aft. The airplane did not display any evidence of a bird strike.

During postaccident testing, all three-landing gear deployed normally using the landing gear bypass valve; however, the landing gear status display showed unsafe indications for the main landing gear. Postaccident photographs of the accident site showed that both the left main landing gear down and up position relay modules had been dislodged from their terminals in the avionics bay, located below the windshield on top of the instrument panel. Once the left main landing gear modules were installed in the terminal bay, the left main landing gear down indications worked normally and indicated down with the landing gear down and locked.

Windshield Examination

The windshield was cast acrylic and the frame was a carbon fiber reinforced polymer (CFRP) with layers of carbon-fiber fabric and epoxy. Most of the windshield was fragmented and departed the airframe in-flight, but portions remained encased in the window frame. (See figure 1) Three pieces along the lower edge of the windshield were easily removed from the window frame. Large portions of the windshield extended beyond the edge of the integral window frame from about the 4 to 6 o'clock and about 6 to 8 o'clock positions. Additional sections of the windshield remained attached to the windshield frame but did not extend beyond the edge of the window frame cutout in the fuselage. The window frame had visible signs of damage to the composite airframe structure at the 2, 6, and 10 o'clock positions.

Figure 1. Forward Face of Windshield

The entire windshield frame was removed, including all of the composite structure to which the windshield was bonded. The composite airframe window frame structure, windshield pieces, and a small section forward of the frame were sent to Wichita State University's National Institute of Aviation Research (NIAR).

NIAR Examination & Limitations

The NTSB and NIAR made multiple requests to Lancair International, Inc. the manufacturer of this experimental amateur built airplane, for engineering data related to the windshield, frame and paste adhesive. The manufacturer failed to provide the engineering and test data required to complete NIAR's analysis, thus their report was inconclusive. The section below contains a summary of NIAR's examination.

A total of 12 windshield artifacts were submitted to the NIAR lab for examination. Visual examination of the two large intact sections of the windshield showed gaps, indicating that the remaining portions were not fully bonded into place. Once the fracture surfaces were documented, the samples were subjected to failure analysis, material and bond evaluation, and paint evaluation.

Due to the limited technical information provided to the NTSB and NIAR, NIAR was unable to continue its analysis of the windshield, frame, and paste adhesive. Specifically, a review of the structural design of the fuselage/windshield design could not be performed as no structural analysis was provided by the manufacturer. Further, a review of the bond strength design values for the bond between the windshield (acrylic) and the window frame could not be conducted due to the absence of bond strength test data for the window to windshield bond from the manufacturer. Finally, the paint scheme restrictions presented in the build manual could not be evaluated due to an absence of the manufacturer's analysis and reasons for these restrictions.

Extensive cracking was found directly in front of the windshield, consistent with delaminated wet-layup plies that were applied to the fuselage after the two fuselage halves were joined together. (See figure 2) These findings indicated significant structural flexing in the fuselage.

Figure 2: Excerpt of Forward Cowling Failure and Fuselage Halves from NIAR Report

Material and Bond Evaluation

According to NIAR, airframe temperatures can reach high levels when the airplane is parked and exposed to solar radiation and adverse ambient conditions.

Glass transition temperature (Tg) is the temperature range where the polymer substrate changes from a rigid glassy material to a soft material and is usually measured in terms of the stiffness or modulus. Thermal analysis was used to evaluate the Tg of the composite windshield frame, acrylic windshield, and paste adhesive used for bonding the windshield to the frame. Testing showed that the average low Tg was 192°F for the paste adhesive, the lowest Tg for the evaluated materials.

At the time of the windshield failure, the outside air temperature (OAT) was recorded as -34°C (-29°F), which had been constant for the previous 6 minutes. For the 15 minutes before that, the OAT was -18°C (0°F). Thus, the windshield frame material was not beyond the Tg at the time of the failure.

Paint Evaluation

Solar reflectivity or reflectance is the ability of a material to reflect solar energy from its surface. Six samples of the airframe were extracted to evaluate the total solar reflectance (TSR) and emittance value, or effectiveness at emitting thermal energy, associated with the aircraft coating used. The TSR values captured for these samples were consistent with a low amount of reflectance and higher heat retention for aircraft coating applications. Airframes with coatings that promote absorption of solar energy (such as dark colors), can reach temperatures outside of the intended operational temperature. In this particular case, the potential risk for the airframe to reach high temperatures was a concern due to the paint color and region of the airplane's home airport in Arizona.

Lancair did not provide the engineering and test data required to complete NIAR's analysis, thus, the results of the analysis and evaluation of the material was inconclusive. Specifically, a review of the structural design of the fuselage/windshield design could not be performed as no structural analysis was provided by the manufacturer. A review of the bond strength design values for the bond between the windshield (acrylic) and the window frame could not be conducted due to the absence of bond strength test data for the window to windshield bond from the manufacturer. Finally, the paint scheme restrictions presented in the build manual could not be evaluated due to an absence of the manufacturer's analysis and reasons for these restrictions.

NTSB Materials Laboratory Examination

The windshield was forwarded by NIAR to the NTSB Materials Laboratory for further examination.

According to the window installation instructions, the exterior surface of the windshield is bonded with Hysol EA 9360 paste epoxy, and the interior surface of the windshield is bonded in place with Rhino 1307-LV resin plus hardener. The windshield remnants and bond surfaces were examined visually, and the directions of fracture propagation were determined.

The windshield remnant at the left side of the frame included a longitudinal fracture (fracture A), and a crack in the lower left side of the windshield was adjacent to the frame (fracture B). Three other adjacent fractures were secondary.

The forward lower end of fracture A was flat and perpendicular to the interior and exterior surfaces across the thickness of the windshield and along the length of the fracture consistent with fracture under mostly tension loading.

Ratchet marks were observed from the interior surface at the origin area of fracture B, indicating a fracture initiation on multiple slightly offset planes from the interior surface. The overall subsequent progression of the fracture from the interior to exterior along the length of the crack was consistent with higher tension stress at the interior surface, indicative of a combination of tension and bending loads during fracture.

The forward end of fracture B intersected with the forward edge of the windshield near the start of fracture A; however, the relationship between fracture B and fracture A could not be determined due to a lack of available evidence.

According to the windshield installation process specified by the kit manufacturer, the edges of the windshield within the frame are roughened by ...