N9970F

HISTORY OF FLIGHTOn June 26, 2022, about 1938 Alaska daylight time, a Bell UH-1B helicopter, N9970F, was destroyed when it was involved in an accident near Clear, Alaska. The pilot was fatally injured. The helicopter was operated by Northern Pioneer Helicopters LLC as a Title 14 Code of Federal Regulations Part 133 external load flight.

The operator reported that the helicopter was stationed at Clear Airport (Z84), Clear, Alaska, to support wildland firefighting operations. The purpose of the flight was to longline equipment to firefighters working on the ground.

Numerous witnesses reported that, after a normal liftoff, the helicopter was hovering with the longline fully extended as it maneuvered to hook up to the external load when a loud “snap” or “bang” was heard. One witness stated that the helicopter “bucked” and that he observed the pilot attempting to regain control of the helicopter as it descended. The helicopter subsequently rolled to the right, entered a nose-low descent, and impacted the ground before bursting into flames.

A witness video camera captured the helicopter’s final seconds before impact with the ground. A review of the recording revealed that that the helicopter was hovering with the 125-ft longline fully extended below the helicopter, and the hook at the end of the line was about 15 ft above the ground. As the pilot maneuvered the helicopter to hook up to the external load, a loud mechanical noise could be heard, after which a shudder is seen radiating through the helicopter’s airframe, followed by an extreme roll to the right past 90°, and a nose-low descent. As the descent continued, the transmission (with the rotor head and blades attached) along with the tail boom separated from the fuselage before ground impact. (See figure 1.)

Figure 1 - Screen capture of the end of the video showing the separation of the main rotor and transmission from the airframe before ground impact. PERSONNEL INFORMATIONAt his most recent Federal Aviation Administration (FAA) medical certification examination, he reported taking rosuvastatin, metoprolol, lisinopril, clopidogrel, and aspirin. He reported a 2017 heart attack with coronary artery bypass surgery of five vessels and coronary artery stenting. He was reported to have had above average exercise tolerance for his age and experienced no chest pain at his most recent stress test. AIRCRAFT INFORMATIONThe accident engine was a LycomingT53L-13B, serial number LE-18935, capable of 1,400 horsepower (hp). The engine was equipped with a five-stage axial and single stage centrifugal compressor, with an external annular combustion chamber, two-stage gas producer turbine, and two-stage power turbine. The power shaft drives the reduction gearbox through the output shaft. AIRPORT INFORMATIONThe accident engine was a LycomingT53L-13B, serial number LE-18935, capable of 1,400 horsepower (hp). The engine was equipped with a five-stage axial and single stage centrifugal compressor, with an external annular combustion chamber, two-stage gas producer turbine, and two-stage power turbine. The power shaft drives the reduction gearbox through the output shaft. WRECKAGE AND IMPACT INFORMATIONThe helicopter impacted the asphalt on the north ramp area of Z84 on its left side in a nose-low attitude and was largely consumed by postcrash fire. The engine’s transmission, with the rotor head and blades still attached, was found about 30 ft from the main wreckage. (See figure 2.)

Figure 2 - Main wreckage

The left seat collective control was present and attached to the torque tube. Neither cyclic control was located. Both of the right seat/side anti-torque pedals had been liberated from their supports. Both left seat/side anti-torque pedals remained attached to their supports and connected to their bell crank.

The tail rotor drive system continuity was established through all of its 5 sections by accounting for the driveshaft connections, hanger bearings, and recovered drive shaft segments. The drive shafts had separated from both ends of the intermediate 42° gear box. The gear box rotated smoothly. The magnetic drain plug was removed and was free of debris.

A postaccident examination of the airframe that included, but was not limited to, the helicopter’s annunciator panel, the left and right lateral servos and collective servo, the hydraulic pump, the tail rotor, and the KAFlex drive shaft revealed no pre-accident mechanical malfunctions or anomalies that would have precluded normal operation.

The NTSB Materials Laboratory examination revealed that the transmission case was fractured on the right side near the aft support. The forward pylon support legs were fractured through the rivets attaching the isolation mount pad to the vertical faces of the legs. The aft left support leg was fractured at the lower attachment bracket for the friction damper, and the aft right support leg was fractured at its lower end. The main transmission and pylon structure likely separated due to overstress fracture. The aft isolation mounts and friction dampers showed evidence of substantial overtravel in the upward direction.

The engine came to rest on its left side and exhibited significant thermal damage. A visual examination of the compressor inlet and power turbine blades did not reveal any blade damage. The postaccident examination of the engine revealed no pre-accident mechanical malfunctions or anomalies that would have precluded normal engine operation. ADDITIONAL INFORMATIONA review of the National Transportation Safety Board (NTSB) accident database found a similar accident that involved pilot-induced oscillations caused by the loss of hydraulic assist of the flight controls due to an excessive loss of hydraulic fluid during a critical phase of flight on a Bell UH-1H helicopter (NTSB accident number CEN13FA415). The NTSB Final Report stated in part:

Following the accident, without FAA or NTSB awareness, two pilots from Billings Flying Service conducted an informal UH-1H flight test at high altitude. The flying pilot notified the NTSB of his findings during an interview. During a simulated long line profile with the hydraulics system turned off, the flying pilot observed a high amount of force was required to apply collective. While making his "hard pull" of the collective with his left arm, the pilot observed that he had a tendency to "brace" himself and push the cyclic to the right, causing a right bank. This tendency to bank right was not immediately recognized, since he was leaning left to simulate sighting for a long line operation. As he attempted to return to a level attitude (with the hydraulics system turned off) he overcorrected and entered into nearly 90 degrees of left bank. The pilot was very startled by the dramatic left bank and immediately directed the other pilot in the right seat to restore hydraulics system pressure to assist with recovery of the helicopter. MEDICAL AND PATHOLOGICAL INFORMATIONAccording to the autopsy report from the State of Alaska, State Medical Examiner’s Office, Anchorage, Alaska, the pilot’s cause of death was blunt force injuries of head, torso, and extremities due to helicopter crash, and the manner of death was accident. The medical examiner reported a gray-white area of the heart consistent with a remote posterior myocardial infarct, the presence of two venous grafts, and 75% stenosis of sections of his coronary arteries.

Toxicology testing performed by the FAA Forensic Sciences Laboratory detected the non-impairing medications rosuvastatin and metoprolol in the pilot’s cavity blood and urine. Rosuvastatin is a member of the drug class of statins, used to treat high cholesterol and related conditions and to prevent cardiovascular disease. Metoprolol is a beta-blocker used in the treatment of hypertension and certain arrhythmias.